Together, EIA and JESDA detail the ESD requirements from the earliest steps in the assembly process to the final packing, shipping, and handling of. JEDEC. STANDARD. Requirements for Handling Electrostatic-Discharge- Sensitive (ESDS) Devices JESDA (Revision of EIA). DECEMBER charging up to dangerous levels (> 1kV) (JEDEC specification JESDA). Verify that machines and microscopes are properly grounded per JESDA.
|Published (Last):||15 May 2006|
|PDF File Size:||10.75 Mb|
|ePub File Size:||11.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
The intent of this document is for users to incorporate these minimal requirements into their ESD control program to provide a consistent ESD protection level for their products. NOTE — Topically treated tubes, trays, magazines and carriers tend to lose their static protective properties with use and should be evaluated periodically for acceptable performance.
Its value shall be within the limits specified in table 2, 1. Adding a Data Visualiz The wire should be attached to physical structures to prevent mechanical damage. As a minimum, audit records shall specify what was audited, the auditor’s name, date of audit, audit results, corrective actions required if applicableand evidence of verification of satisfactory completion of any required corrective actions.
When the supplier’s original packing materials and containers are noncompliant to this standard, the ESDS devices shall be rejected and returned in the original materials and containers. The requirements within this standard were derived from existing industry standards, specifications, test methods, and input from various industry reviews.
Referring to the property of material that inhibits triboelectric charging. Records shall be maintained for at least two 2 complete years. The point, electrodes, bus bar, metal strips, or other system of conductors that form a path from a statically charged person or object to ground. Applying or removing static generating tapes and labels to antistatic tubes, magazines and carriers shall not be done with ESDS devices inside.
Equipment ground is the electrical ground green wire at receptacles that have been tested to and meet the requirements of NFPA or local equivalent. Prior to probe, the manufacturer should take appropriate ESD precautions to minimize damage to devices.
ESD Protective Smocks 6. The ESD caution label on the package may be provided by a preprinted marking on the package or its sealing tape.
REQUIREMENTS FOR HANDLING ELECTROSTATIC-DISCHARGE-SENSITIVE (ESDS) DEVICES | JEDEC
A short form of electrostatic. When a floor grounding device e.
A resistor in the grounding wire is optional. NOTE — Substantial generation of static electricity can be caused by contact and separation of two materials or by jesc625 two substances together. The caution label shall be legible to normal vision at a distance of three feet. A material having a surface resistance between jesd62 x ohms and 1 x ohms or a volume resistivity between 1 x ohm centimeters and 1 x ohm centimeters.
Recommended Weekly a ESD protected workstation. The transfer of electrostatic charge between bodies or surfaces that are at different electrostatic potentials. A packaging system that provides electrostatic protection and limits triboelectric charging to levels that do not result in device damage. Where both grounds are used, they shall be connected bonded together. Use of alligator clips is not recommended. A material having a surface resistivity of at least 1 x ohms per square or volume resistivity of at least 1 x ohm centimeter.
When both equipment and earth grounds are used at the same ESD protective workstation they shall be bonded together at some point in the ground system.
REQUIREMENTS FOR HANDLING ELECTROSTATIC-DISCHARGE-SENSITIVE (ESDS) DEVICES
As a minimum, the records shall show dates of training, length of training session, topics covered, and the name of the trainer. NOTE — The electrical charge is due to the transfer of electrons within a body polarization or from one body to another. Wire splices should be crimped or soldered. The entire low-impedance path from a piece of electrical equipment to a hardground electrode e.
By downloading this file the individual agrees not to charge or resell the resulting material. NOTE — ESD controlled packing materials that will be inside wafer and die containers should be selected to avoid contamination of the devices. A table top or other surface on which to work that has a resistance to ground of less than ohms ground: Static Generating Sources and Charged Surfaces 5. Air velocity measurements are not required.
Where the choice of color is arbitrary, it is suggested that the symbol be black on a yellow background. Corrective actions resulting from monitor alarms shall be documented. When ESD protective smocks are worn, they shall cover all personal garments above the waist except at the neck area.
When more than one ESD worksurface is used at mesd625 workstation, each surface shall be individually connected to the X ground. The ionizer shall be aimed at the devices and operator’s hands rather than at the operator.
Recommended Quarterly ESD protected area and workstation static voltage surveys.
During application of any antistatic chemical, the user must consider the following: A typical grounding system for an ESD protected workstation is illustrated in figure 1. Grounded flooring or floor mats are only required when personnel or mobile ESD protective workstations utilize floor grounding methods. NOTE 1 Volume resistivity is generally expressed in ohm centimeters.
A source of charged air molecules ions. The passage of a static charge through an electrostatic-discharge-sensitive ESDS device can result in catastrophic failure or performance degradation of the part.
Monochromatic reproduction in any color that contrasts with the background may be used.
JESDA ESD Handling Dec, _图文_百度文库
Those with mid-to-lower resistance values provide shorter charge dissipation times. Lines of force surrounding an electrically charged object. The lowest level of ESD that produces changes in device characteristics such that the device fails to meet its specified characteristics.