ZONE AMPLIFIER ZAA ZAA C AUTION AVIS 1 SAFETY INSTRUCTIONS 1 GENERAL USE (용도) 1 I NSTALLATIONS 2 F. Jedia JPAA/JPAA Amplifier Functions · JPAA Operating Instructions. Legislation and Compliance. RoHS Status: Not Applicable. Statement of. מגברי JDM היפרטרוניקס רכיבים וחלקי אלקטרוניקה מערכות כריזה והגברה מוצרי חשמל מגבר מיקסר חכם ל- 5 איזורי כריזה W. ZAA: A/A. ZAA: A/
|Country:||Papua New Guinea|
|Published (Last):||19 October 2013|
|PDF File Size:||7.80 Mb|
|ePub File Size:||20.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
Never block the air vents in the sides and front of the amplifier the following is figure of air-flow. Please pay close attention to the cooling requirements. Operation voltage for mic priority is DC 24V to the screw terminal. It is best suited for call and message transmission installation with alert systems, music in industrial enterprises, offices, congregation halls and sport centers, schools, churches, hospitals, super-maket, and other similar zaa-1120a.
This is to prevent is to prevent mistake from remote controller RC This is RJ45 connector for power supply of audio, data, make sure that 4pairs LAN cable is necessary for optimum operation.
Connect the power za-1120w with safety after check of AC power. Busy means under operating of “TALK” or digital message. T remote PTT level. T MIC remote jdj. To z-1120a electric shock, do not open top cover.
You can hear telephone ring Via speaker from other office in the night. Users can extend cable at 30m MAX. If all call switch, P.
Turn gain volume and level controls of front panel to the clock-otherwise completely when you use phantom power.
Announcement only for M6 alertvoice message P. The corresponding LED indicator lights. Use LAN cable within m distance. Cable for audio line should be used by shield cable. Maximum power output per zone speaker.
מגברי JDM | מגבר מיקסר חכם ל- 5 איזורי כריזה W | היפרטרוניקס
In case data are supplied to amplifier, send LED indicator lights. The apparatus shall not be exposed to dripping or splashing and no object filled with liquids, such as vases, shall be place on the apparatus. If clip indicator of output meter is turn-on, please turn GAIN control to the clock-otherwise for the optimum internal operstion. If not, speaker may get harmful due to loud noise power by power shock. This apparatus should be serviced by qualified service person. Be sure rear of amplifier is securely mounted to rack.
Connect each connection of amplifier perfectly, if not, it maybe Caused hum, damage, electric shock in case of mis-connecting.
Keep in mind the following when connecting the apparatus. Third, contact terminal to what you want. For the direct output, use spk zone 4 and set speaker ATT. All signal output of remote controller RC will be closed under setting “on” of priority switch on the rear of P.
Locate this apparatus away from heat source, such as radiators or other device that produce heat. For phantom, please push phantom switch to supply with P. Do not install this apparatus in a confined space such as a book case or similar zq-1120a. The stereo signal of the connected sound sources gets internally converted into a manual signal. This makes you replay, stop recorded message of the memory bank M1-M6 one time without setting repeat function.
It’s a community-based project which helps to repair anything.
When not using microphoneturn microphone “off”. Second, you can increase input volume to the position “0” of LED indicator.
Amplifier P.A. 5 zone JDM ZA-1120A
Remote controller RC is prior to any other prioroty priority is activated, an signals are closed But, P. Check inside temperature of rack system so as not to be more than 40 C for the stable operating in any case, we recommend you to install cooling fan additionally on the rear panel of rack cabinet. Out put impedance should be ohms more for pre-amp operation.
Install equipment as follow conditions. Then, attenuation function in the main amplifier are reset and zone power-out is converted to HI impedance power output. All signals can be recorded but recording out can not be adjusted by master volume because recording output is in the front of circuit of master volume control.
מגבר מיקסר חכם ל- 5 איזורי כריזה 240W
This is for pre signal or alert signal. Pressing one of the zone button 1 to 5 delegates the signal to the desired loud speaker zone. This function is same as that of “TALK” or “message” operation.