HCNW 4504 PDF

HCNW Broadcom / Avago High Speed Optocouplers 1Ch 12mA mW datasheet, inventory & pricing. The HCPL and HCPL contain a GaAsP LED while the. HCPL-J and HCNW contain an AlGaAs LED. The LED is optically coupled to an. Buy Broadcom HCNW# in Avnet Americas. View Substitutes & Alternatives along with datasheets, stock, pricing and search for other Transistor .

Author: Kajidal Shajind
Country: Guadeloupe
Language: English (Spanish)
Genre: Software
Published (Last): 23 April 2005
Pages: 298
PDF File Size: 4.5 Mb
ePub File Size: 19.74 Mb
ISBN: 957-2-25294-593-4
Downloads: 36492
Price: Free* [*Free Regsitration Required]
Uploader: Akinogar

These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements.

HCNW Broadcom Limited|Optoisolators – Transistor,Photovoltaic Output | WIN SOURCE

The LED is optically coupled to an integrated high gain photo detector. It is important to maintain accurate LED turn-on delays because delays shorter than tPLH – tPHL max may allow shootthrough currents, while longer delays will increase the worst-case dead time.

Use of nonchlorine activated fluxes is highly recommended. Calculating the maximum dead time is slightly more complicated.

Propagation Delay Time vs. Current Transfer Ratio vs. Use of a 0.

Agilent Technologies HCNW4504 Optocoupler Lot -5

Contact Agilent sales representative or authorized distributor for information. Minimizing this dead time is an important design goal for an inverter designer.

Extremely large currents will flow if there is any overlap in their conduction during switching transitions, potentially damaging the 404 and even the surrounding circuitry.

The timing illustrated in Figure 17 assumes that the power transistor turns on when the optocoupler LED turns on. The LED signal to turn on Q2 should be delayed enough so that an optocoupler with the very fastest turn-on propagation delay tPHLmin will never turn on before an optocoupler with the very slowest turn-off propagation delay tPLHmax turns off. F bypass capacitor connected between Pins 5 and hhcnw is recommended.

  DESCARGAR MANUAL DE RADIOLOGIA PARA TECNICOS BUSHONG PDF

(PDF) HCNW4504 Datasheet download

There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. These optocouplers are suitable for “safe electrical isolation” only within the safety limit data.

See Option data 454 for more information. Most inverters are designed such that the power transistor turns on when the optocoupler LED turns on; this ensures that both power transistors will be off in the event of a power loss in the control circuit. Inverters can also be designed such that the power transistor turns off when the optocoupler LED turns on; this type of design, however, requires additional jcnw circuitry to turn off the power transistor if an over-current condition is detected.

When inverter power transistors switch Q1 and Q2 in Figure 17it is essential that they never conduct at the same time. F bypass capacitor between pins 5 and 8 is recommended. The importance of these specifications is illustrated in Figure For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered.

Device considered a two-terminal device: Logic High Output Current vs. Separate connections for the photodiode bias and outputtransistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base collector capacitance. For technical assistance call: Option data sheets hdnw. Although tPLH-tPHL max tells the designer how much delay is needed to prevent shoot-through hchw, it is insufficient to tell the designer how much dead time a design will have.

  GAUTHIER CONNECTIQUE PDF

The Input-Output Momentary Withstand Hnw is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. The difference between the maximum and minimum values depends directly on the total hcna in propagation delays and sets the limit on how good the worst-case dead time can be for a given design.

HCNW – IC Chips,Purchase HCNW online with free shipping | UTSOURCE

DC and Pulsed Transfer Characteristics. Under TTL load and drive conditions: An insulating layer between a LED and an integrated hvnw provide electrical insulation between input and output.

Therefore, optocouplers with tight propagation delay specifications and not just shorter delays or lower pulse-width distortion can achieve short dead times in power inverters. However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards.

To ensure this, the turn-on of the optocoupler should be delayed by an amount no less than tPLHmax – tPHLminwhich also happens to be the maximum data sheet value for the propagation delay difference specification, tPLH – tPHL. Maintenance of the safety data shall be ensured by means hcns protective circuits.

Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. Pins 1, 2, 3, and ycnw shorted together and Pins 5, 6, 7, and 8 shorted together.

VPN