Manufacturer Part No: HCNRE. Order Code: Technical Datasheet: HCNRE Datasheet. See all Technical Docs. Broadcom HCNRE: available from 15 distributors. Explore Optoelectronics on Octopart: the fastest source for datasheets, pricing, specs and . HCNR/HCNR is UL Recognized with Vrms for 1 minute per UL . Mount. Wing & Reel 1 Minute rating VIORM = Vpeak. Quantity. E.

Author: Tugrel Daimi
Country: Pakistan
Language: English (Spanish)
Genre: Automotive
Published (Last): 4 May 2018
Pages: 469
PDF File Size: 7.20 Mb
ePub File Size: 7.61 Mb
ISBN: 773-9-94363-733-6
Downloads: 76478
Price: Free* [*Free Regsitration Required]
Uploader: Arajinn

Data Sheet HCNR and HCNR High-Linearity Analog Optocouplers |

The first circuit has the obvious advantage of requiring only one optocoupler; however, the offset performance of hnr201-000e circuit is dependent on the matching of IOS1 and IOS2 and is also dependent on the gain of the datashete. External Creepage L IO2 HCNR fig 2 0. Device considered a two-terminal device: Besides the optocoupler, two external op-amps and two resistors are required. Page 3 Package Outline Drawings Elcodis is a trademark of Elcodis Company Ltd.

This would reduce the loop gain of the input circuit, reducing circuit accuracy and bandwidth. The output circuit does not directly generate an output voltage which is sensed by R2, it instead uses Q1 to generate an output ycnr201-000e which flows through R3. Contact your Avago sales representative or authorized distributor for information. Protective cut-out switches must be used to ensure that the safety limits are not exceeded. High-speed low-cost analog isolator. Also notice that IPD1 is exactly proportional to VIN, giving a very linear relationship between the input voltage and the photodiode current.

IMRR is defined as the ratio of the signal gain with signal applied to VIN of Figure 16 to the isolation mode gain with VIN connected to input common and the signal applied between the input and output commons at 60 Hz, expressed in dB. These capacitors also limit the bandwidth of the circuit to about 10 kHz and can be used to reduce the output noise of the circuit by reducing its bandwidth even further. The input pho- todiode can be used to monitor, and therefore stabilize, the light output of the LED The two OP-AMPS shown are two separate LM, and not two channels in a single dual package, otherwise the loop side and output side will not be properly isolated.


Diodes D1 and D2 help reduce crossover distortion by keeping both amplifiers active during both positive and negative portions of the input signal.

HCNRE datasheet and specification datasheet. As mentioned above, only one optocoupler is used. Option datasheets are available. The relationship between the input optical power and the output current of a photodiode is very linear. And R7 is selected so that Q4 operates datasehet about the same collector current as Q2. Parameter Symbol Device Min.


It is advised that normal static precautions be taken in handling and assembly. Download datasheet Kb Share this page. Gull Wing Surface Mount Option Because a photodiode can conduct current in only one direction, two diodes D1 and D2 are used to steer the input current to the appropriate terminal of input photodiode PD1 to allow bipolar input currents. Loop-powered mA current loop circuits. All other trademarks are the property of their respective owners. Example Application Circuits The circuit shown To achieve very high linearity for bipolar signals, the gain should be exactly the same for both positive and negative input polarities.

As a result, the non-linearity. The output photodiode produces a photocur rent.



Package Outline Drawings The circuit operates in the same manner as well; the only difference is the performance of amplifiers A1 and A2. It’s a community-based project which helps to repair anything.

It is also possible to convert this circuit into a fully bipolar circuit with a bipolar output signal by using the output of the 6N to drive some CMOS switches to switch the polarity of PD2 depending on the polarity of the input signal, obtaining a bipolar output voltage swing.

External Clearance L IO1 9. For example, when the input signal positive, optocoupler OC1 is active while OC2 is turned off. R3 and R5 are selected to provide enough current to drive the bases of Q2 and Q4. Data subject to change.

The lower gains, higher input currents and higher offset voltages affect the accuracy of the circuit, but not the way it operates. LED input current vs. Typical photodiode leakage vs. The fi nal circuit shown in Figure 19 isolates a bipolar analog signal using only one optocoupler and generates two output signals: IORM peak Example 2: High Datashedt High Precision 1.

Units Test Conditions Fig. However, an additional amplifier is used to provide an appropriate offset voltage to the datashet amplifiers that exactly cancels the diode voltage drops to maintain circuit accuracy.

Because the basic circuit operation has not changed, the circuit still has good gain stability. A Parameter Symbol Input-Output The basic optocoupler con- sists of an LED and two photodiodes.