DIN 8593-5 PDF

Standards. DIN Manufacturing processes joining – Part 5: Joining by forming processes; Classification, subdivision, terms and definitions. Title ( German). DIN references following documents: DIN , , Manufacturing processes joining – Part 5: Joining by forming processes; Classification. Find the most up-to-date version of DIN at Engineering

Author: Momi Voodoocage
Country: Denmark
Language: English (Spanish)
Genre: Technology
Published (Last): 17 September 2009
Pages: 367
PDF File Size: 19.10 Mb
ePub File Size: 14.78 Mb
ISBN: 175-1-12022-795-2
Downloads: 16229
Price: Free* [*Free Regsitration Required]
Uploader: Kemi

In the latter case, the microsection must be prepared so that the microsection plane is located in the center of the clinched joint for the determination of the geometric characteristics.

Metallic continuity may occur under certain conditions. Skip to main content Skip to table of contents.

Joining by Upset Bulging | SpringerLink

The joints were prepared for the three combinations of the DC01 steel and EN AW- aluminium alloy sheets with the thickness of 2mm. For sheets with different plasticity characteristics, the 85993-5 sheet is to be arranged on the side of the punch wherever possible “hard in soft”.

From all sheets and rivet specimens arrangements the highest load capacity of the joint was obtained for the DC01 sheet material joints, and the lowest load capacity of the joint was obtained for the EN AW sheet material joints.

Such processes are necessary to fulfill the growing demands on industrial production of multi-material joints and general lightweight production.

Joining by Upset Bulging

If the base is cracked, check for microsection preparation errors. User Account Sign in to save searches and organize your favorite content.

  BELDEN 9292 PDF

Undercut f not present on both sides: Previous issues VW No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the Volkswagen Group.

Considerably lower strength is to be expected if this is not the case. Mechanical djn ; Tube forming ; Upset bulging. With segmented dies, the microsections must be located in the center of the die segments.

Dun case of discrepancies the German version shall govern. Especially for round joints, care must be taken that the joint does not fall apart when preparing the microsections. This is a preview of subscription content, log in to check access.

If undercut is present on both sides: Synonyms Mechanical joining ; Tube forming ; Upset bulging.

Drawing version desired values of the joint: There are no generally applicable values for the base thickness tb. The resulting clinched joints are also referred to as joints in the following. In this Section terminological inconsistencies may occur as the original titles are used.

Rectangular joints are to be located perpendicular to the load direction. Here, at least the ratios specified in Table 6 must be achieved: It 85935 be ensured that the joints are not stressed when the sheets are bent e.

The Structure of the Strength of Riveted Joints Determined in the Lap Joint Tensile Shear Test

Joining by forming processes; Classification, subdivision, terms and definitions Clinchen -? These bulges are used to clamp a joining partner e. The flange height is 35 mm Aalternatively 16 mm B. Page 8593- VW The article presents the analysis of the structure of the load capacity of riveted joints.

  ATLANTISZ ANGYALAI KNYV PDF

Table 5 — Abbreviations FLS Measured lap-shear force of the individual specimens [kN] Mean value of the ein lap-shear forces [kN] Fmin Minimum value of the 5893-5 force according to drawing [kN] As rough values e. J Mater Process Technol 5: Air and Exhaust manage Joining by upset bulging is a mechanical joining process, which is commonly used to create joints with a form and force fit between tubes and other structures, such as sheets, plates, tubes, or profiles.

An axial compression load is usually applied to a rotation-symmetric workpiece e. If the material flow in the structure is uninterrupted, as can be seen in the Figure on the left, it is a wrinkle.

De Gruyter – Sciendo. Page 17 VW In particular, conventional fusion welding processes reach their limits due to high heat input The result Fmin Ftransverse — 2 sigma is a reference value for the drawing specification. Clinching allows for joining of both similar and different materials.

Knickbauchen; Einordnung, Unterteilung, Begriffe — [Manufacturing processes forming under combination of tensile and compressive conditions — part 6: The joints must be carried out such that window bonding material can be pressed into the recess created by the joining process, see Figure 4.

VPN