Préampli-Processeur CHORD DSP R VENDU TRÈS RARE! Préampli processeur exceptionnel en HC et, fait beaucoup plus rare. Chord dsp r preamp / surround controller, boxed. CHORD DSP R preamp/ surround controller. with dts and dolby 2 surround. Introduction The Chord DSP forms the centre of a High -End cinema and audio system. The DSP decodes Dolby Digital, DTS and DTS-ES and has the.
|Published (Last):||19 June 2010|
|PDF File Size:||1.51 Mb|
|ePub File Size:||7.81 Mb|
|Price:||Free* [*Free Regsitration Required]|
This chorc happen due to video processing – in projectors, plasma screens and standalone video processors. Press this LCD touch pad to move upwards through the sub menus within the set up menu. This dsp8000g located in the bottom right corner of the display area. However they can also be used as an additional record output.
The OSD signal is also added at this output. This is so that you hear the full surround image as intended regardless of your speaker configuration. Plug the dsp8000e end socket of the mains cable into the power connector of the DSPand the male end plug of the mains cable into mains wall socket or mains extension socket.
As digital signals they are then ready to be decoded or post-processed by the processor. After pressing ENTER then you can change cycle through the available letters, symbols and numbers with the front panel cursor up?
CopyrightDigital Theatre Systems, Inc. We do not recommend that you place your processor directly on a carpet.
Lip sync delay This setting allows you to delay the sound to match the picture if the two are out of synchronisation with each other. Thank you for choosing the Chord DSP for your audio and video signal requirements.
When the outputs are muted, the blue LED in the button will illuminate. LCD touch pads from page 1 of the DSP remote control menus to adjust the level of each loudspeaker setting.
There are five presets to choose from.
Use a sound pressure level SPL meter at the normal listening position to measure the level of each loudspeaker tone. The remote control is preprogrammed with infrared codes for all Chord products. Size setup Used to define which speakers are present and whether they can handle low frequencies. Analogue Monitor This is a link to a special screen, that is available on the on screen display only, where you can adjust the analogue sensitivity gain setting.
Centre This setting allows you to control the level of the centre speaker for the selected preset. The unit can be set up with the comprehensive on screen display facility or via the front panel controls. Pin 1 is earth, pin 2 is positive and dsp800r 3 is negative.
Infin Trigger 2 sense: Analogue audio connections can be split into dsp8000d groups; unbalanced and balanced. Lipsync delay Preset This setting calls up any one of the 5 five presets and its currently saved levels.
If this is set to Infin. If this LCD touch pad is pressed whilst not in the menus then the touch pad functions as an active input source search touch pad.
DSP 8000 AV Processor
PL II Width This control allows centre-channel sounds to be positioned between the centre speaker and the left -right speakers over a range of eight steps. Of course you can also use the remote control cursor up? We recommend that an earthing method for your building be implemented. This processing mode offers a natural sound with no reverb added.
This takes a few minutes to complete. Unbalanced inputs use RCA phono connectors that are gold plated with teflon high performance dielectric in sulators for optimum performance. This is done to keep the highest quality signal for component replay. Press and hold this button to decrease the volume more rapidly.
吏?? ?濡 GLV – Create arts through technology!
This processing mode will copy the left and right channels to the left and right surround channels. This function is called Late Night as it is useful to use late at night when you do not wish to listen to loud and dynamic soundtracks.
S-Video or Component Video connections are preferred as they offer better quality video signals than Composite Video. The distance is therefore not applicable and cannot be changed. Press this button to decrease the value of a selected parameter within the set up menus. Allows direct level calibration using the supplied microphone.