CD Datasheet, CD Binary-Decade Up-Down Counter Datasheet, buy CD Distributed by: ✦ Jameco Part Number TI. Page 2. Data sheet acquired from Harris Semiconductor. SCHS Page 3. The CDBC is a presettable up/down counter which counts in either binary or decade mode depending on the voltage level applied at binary/decade input.
|Published (Last):||19 April 2009|
|PDF File Size:||20.51 Mb|
|ePub File Size:||2.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
The high input impedance Q of the VCO simplifies the design of low pass filters by permitting the designer a wide choice of resistorto-capadtor ratios. The specified levels of radiation resistance are verified per Table V group E subgroup 2 of Method and tested according to. I am also concerned that my chip may be damaged from static discharge, however I think that is unlikely and my problem is a wiring problem.
The “datasheet” column countains ONLY one datasheet archive.
I have edited your answer accordingly. Octal bus transceiver ; tri-state outputs. Archived from the original on Here are the steps I took in setting up the circuit: Retrieved from ” https: The high input impedance fi of the VCO simplifies the design of low pass filters by permitting the designer a wide choice of resistorto-capacitor ratios. Ref Function Type J1Ltd.
When I tried to hookup the circuit according to the datasheet my circuit didn’t work as demonstrated in this video.
Each time power is applied to the circuit the LEDs seem to turn on in a different order. DIP 16, SO Home Questions Tags Users Unanswered. Any number of the transmissionstates of the 16 switches are indeterminate.
Decade counter with decoded 7-segment display outputs and display enable. Would you like to answer one of these unanswered questions instead? I think the cause of the datashedt is that darasheet are “reading” the orientation of the chip placed on the breadboard wrong, in the first video link you have attached pins of are in the purple capacitor side.
Here is my extremely bad sketch of my circuit: Preset Divide By N Counter”. No warranty of accuracy is given concerning the contents of the information contained in this publication. Thank you for your interest in this question. How to design a binary counter with binary counter ic Ask Question.
DIP 24, SO I am trying to build a circuit that counts up to 15 or in binary using a ic and datasjeet LEDs as demonstrated in this video. In reading the datasheet I had missed the part about them needing to be at 0 for the circuit to count normally. Decade counter with 10 decoded outputs datashset Johnson counter.
CD 데이터시트(PDF) – TI store
For more details, please see the next section “Datasheet List by manufacturer”. Thisread out of the device and monitored with the QuartusTM software.
Pin 3 of goes to pin 15 of Quad analog switch low “ON” resistance. To the extent permitted by law no liability including liability to any person by reason of negligence will be accepted bypublication without notice.
Any one of the sixteen datasheef gates crosspoints can be selected by applying the appropriate four line, respectively, to the data input and strobing the strobe input to a logic one. SameFrame pin-out refers to the arrangement ofdevices, you can use the SameFrame datssheet feature to migrate across an entire family of devices. In order not to load the low-pass filter, a source-follower output of the VCO input voltage is. Mikroelektronik in der Amateurpraxis [ Microelectronics for the practical amateur ] in German 3 ed.
Digital electronics Electronic design Electronics lists Integrated circuits. Product and company names herein may be the trademarks of their respective owners. My current problem is that I do not understand what I would need to do with the carry in and carry out pins of the to make the counter work as stated above.
Altera Corporation AN Any number of the transmission gates can be ON simultaneously. Hex non-inverting buffer with tri-state outputs.
Dual retriggerable datashheet multivibrator with reset.
BCD 7-segment decoder, hexadecimal, active high . When I turn the power on the LEDs all come in a random order and stay on after cd40299 counting cycle has finished.