ASTM F788 PDF

Designation: F /F M â 07 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This. ASTM F/FM: Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series. Designation: F /F M – 05 Standard Speci?cation for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This.

Author: Zuluktilar Vudolmaran
Country: Andorra
Language: English (Spanish)
Genre: Life
Published (Last): 5 April 2009
Pages: 258
PDF File Size: 14.8 Mb
ePub File Size: 15.9 Mb
ISBN: 577-9-58167-319-5
Downloads: 60904
Price: Free* [*Free Regsitration Required]
Uploader: Gulrajas

NOTE 1Forging cracks within the limits of this specification may beunsightly, but do not affect the mechanical properties or functionalrequirements of the bolt.

Users of this standard are expressly advised that determination of the validity of any such awtm rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. They are not planished during forging. Register for a trial account. Types of Surface Discontinuities see TerminologyF for definitions not provided 4. Shear bursts occur most frequently at the periphery of productshaving flanged or circular heads. Appendix 2 astm d Types of Surface Discontinuities see Terminology F for de?

Published on Nov View Download Current edition approved Oct. If you like to setup a quick demo, let us know at support madcad.

Current edition approved Nov. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Combining values from the two systems may result in nonconformance with the speci? Inspection and Evaluation 6. Historical Version s – view previous versions of standard.

  ESPLENECTOMIA EN PERROS PDF

Voids are produced by marks or impressions aetm chips shear burrs or by rust formation on the raw material. ASTM A – If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

ASTM-F/FM-, 0 –

Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. Acceptance shall be based on the requirements of S1. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend.

There are no ISO standards for surface discontinuities on any inch-series products. Shear bursts may also occur on the sides of hex-head products. This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of MPa and higher; and inch series products with nominal diameters of No. Acceptance shallbe based on the requirements of S1. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.

This standard has been approved for use by agencies of the Department of Defense. The valuesstated in each system are not exact equivalents, therefore, eachsystem must be used independently of the other. Types of surface discontinuities are: Typical shear bursts areshown in Fig.

  DE LIBERTATE CHRISTIANA PDF

ASTM F788 – 13(2018)

Are you sure you want to empty the cart? It is informational only and not an official part of the standard; the full text of the standard ast must be referred to for its use and application.

There were no books found for the applied search filters. For metric series products, D and Dc are in millime-tres; for inch-series products, D and Dc are in inches. Typical tool marks are shown in Fig. Limits are specified in 5. Copyright Compu-tecture, Inc. The section shall be astmm for microscopic examination in accordance with Test Method E Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

Typical tool marks are shown in Fig. Combining values from the two systems may result in non-conformance with the standard.

Combining values from the two systems may result in nonconformance with the specification. ASTM B – ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, astn or up to date.

This standard has been approved for use by agencies of the Department of Defense.

VPN