ASTM E1086 PDF

Buy ASTM E TEST METHOD FOR ANALYSIS OF AUSTENITIC STAINLESS STEEL BY SPARK ATOMIC EMISSION. ASTM E Standard Test Method for Analysis of Austenitic Stainless Steel by Spark Atomic Emission Spectrometry. standard by ASTM. ASTM E – Standard Test Method for optical emission vacuum spectrometric analysis of stainless.

Author: Fenribei Zolobar
Country: Madagascar
Language: English (Spanish)
Genre: Finance
Published (Last): 18 May 2012
Pages: 59
PDF File Size: 9.23 Mb
ePub File Size: 11.99 Mb
ISBN: 269-4-22042-672-6
Downloads: 40050
Price: Free* [*Free Regsitration Required]
Uploader: Fegrel

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. E11086 edition approved Jan. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Refer to Practice E Any of these that will achieve 1e086 accuracy equivalent to that reported for this test method are acceptable.

ASTM International – Standard References for ASTM E – 14

The interlaboratory testing was conducted in accordance with Practice E Make the necessary corrections either by adjusting the controls on the readout or by applying arithmetic corrections.

B Either iron line Historical Version s – view previous versions of standard. Grinding materials with grit sizes ranging from 60 to have been found satisfactory. These data were obtained by procedures outlined in Practice E Calculation of Results A variety of such systems are commonly used. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

  CRAWFORD SHOP CLASS AS SOULCRAFT PDF

Link to Active This link will always route to the current Active version of the standard. The results for each individual laboratory is on? A minimum of three reference materials shall be used for each element. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This represents a total of 15 determinations.

The samples must be sufficiently massive to prevent overheating during the discharge and of a similar metallurgical condition and composition as the reference aatm. Flush, s Preburn, s Exposure, s 2 10 10 or 15 Argon Flow 0. One or more of the reference materials must closely approximate the composition of the specimen. Reagents and Materials 7.

Standardization will be done anytime veri? A superscript epsilon e indicates an editorial change since the e086 revision or reapproval. A variety of such systems are commonly used.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This procedure is suitable for manufacturing control and inspection testing.

Active view current version of standard. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

Examine the specimen after each excitation to evaluate the quality of excitation. Calibration, Standardization, and Veri? The stand shall provide an atmosphere of argon and may be water cooled. Work Item s – proposed revisions of this standard. Cool the specimen after two excitations to prevent overheating, aetm required.

  DIMITRI BERTSEKAS ROBERT GALLAGER DATA NETWORKS PRENTICE HALL PDF

The agreement between the results obtained by chemical methods and those obtained by this test method is displayed in Table 3. Capacitance d-c charged ,? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to s1086.

Successive excitations shall be sufficiently separated so that the discharge patterns do not overlap.

Avoid the center of cast specimens because there is more chance of quench cracks and segregation. Prepare the surface to be analyzed on a suitable belt or disk grinder. There shall be at least three calibrants for each element, spanning the required concentration range. Follow the procedure for the concentration-ratio method in accordance with Practice E E — 94 Position the specimen so there will be a uniform pattern of excitations around its face.

A number in parentheses indicates the year of last reapproval.

ASTM E1086 – 14

Link to Active This link will always route to the current Satm version of the standard. One or more of the reference materials must closely approximate the composition of the specimen. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. This procedure is suitable for manufacturing control and inspection testing.

VPN