ASTM D5587 PDF

Tear test of Fabric by trapezoid method to ASTM D ASTM D covers the measurement of the tearing strength of textile fabrics by the trapezoid tear test using a constant-rate-of-extension-type (CRE) tensile. ASTM D Tearing Strength of Fabric by. Trapezoid Procedure. • Scope – this test method describes the determination of the tearing strength of fabrics by the.

Author: Fenrilar Dikora
Country: French Guiana
Language: English (Spanish)
Genre: Finance
Published (Last): 6 August 2005
Pages: 118
PDF File Size: 1.37 Mb
ePub File Size: 6.86 Mb
ISBN: 719-3-54473-823-3
Downloads: 10861
Price: Free* [*Free Regsitration Required]
Uploader: Mazilkree

Current edition approved Feb.

ASTM D – tearing strength of fabrics by the trapezoid procedure

The three woven fabric types were: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. As a minimum, use the samples for such a comparative test that are as homogeneous as possible, drawn from the same lot of material s5587 the samples d55877 resulted in disparate results during initial testing.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

This test method allows the use of the CRT-type tensile machine when agreed upon between the purchaser and the supplier. When specimens are to be tested wet, take the specimens from areas adjacent to the dry test specimens.

It is useful for estimating the relative tear resistance of different fabrics or different directions in the same fabric. Software for Series Systems.

The method specifies a procedure to determine the tear force of textile fabrics using the trapezoid method. The separation of the jaws is increased continuously to apply a force to asym the tear across the specimen.

G Hydraulic Vice Action Grip. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Email addresses can only contain letters, numbers and the following special characters: If any of d5587 modications are used, state the method of modication in the report.

  COMMENT UTILISER XLSTAT PDF

Tear Strength of Fabrics – Trapezoid Procedure

Strong fabrics or fabrics astmm from glass fibers require special adaptation to prevent them from slipping in the clamps or being damaged as a result of being gripped in the clamps. Disengage the pawls from the rachet to render them inoperative. Ensure specimens are free of folds, creases, or wrinkles. At the qstm time, the force developed is recorded. The specimen is slit at the center of the smallest base of the trapezoid to start the tear.

Within this limitation, this test method has no known bias. The values stated in inch-pound units may be approximate. In any event, the CRE-type machine shall prevail.

ASTM D – 15 Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure

The average results from the two laboratories should be compared using the appropriate statistical analysis and an acceptable probability level chosen by the two parties before testing is begun. Concrete, Asphalt and Rock. Subscribe to Our Newsletters. Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience.

Consequently, no multi-fabric comparisons were made.

ASTM D5587 Tearing Strength of Fabrics by Trapezoid Procedure

A rectangular specimen is marked and prepared so that it can be loaded in the astmm faces at an angle, allowing a tear to propagate s5587 the specimen. It is ast responsibility of the user of this standard to establish appropriate safety and health practices and asgm the applicability of regulatory limitations prior to use. NOTE 2—The tabulated values of the critical differences should be considered to be a general statement, particularly with respect to betweenlaboratory precision. Label to maintain specimen identity.

  BERNARDO ESQUINCA PDF

Strong fabrics or fabrics made from glass bers require special adaptation to prevent them from slipping in the clamps or being damaged as a result of being gripped in the clamps. Describe the fabric or product sampled and the method of sampling used. Have a question about conducting the test for this standard? The minimum tearing force, however, is indicated to be above the lowest valleys.

It is recognized that some constant-rate-of-traverse-type CRT tensile testing machines continue to be used. If bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.

The challenges of testing to this standard are: The conditions for use of the CRT-type tensile tester are included in. The valleys recorded between the peaks have no specic signicance.

Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models.

Consequently, these two tensile testers cannot be used interchangeably unless the degree of quantitative correlation has been established between the purchaser and the supplier. The tearing force may increase to a simple maximum value or may show several maxima and minima, as shown in Fig.

Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

VPN