Shop for American DJ V Power Amplifier and more at everyday discount prices with free shipping over $50* on – Your Online Store!. Buy the ADJ V Amplifier at PlanetDJ. Low VIP Pricing, Financing and Free Shipping available. American Audio | V | User manual | American Audio V User manual American Audio┬« – – V Vplus Series Amplifiers Power.

Author: Namuro Fenritaxe
Country: South Sudan
Language: English (Spanish)
Genre: Automotive
Published (Last): 15 August 2009
Pages: 200
PDF File Size: 9.80 Mb
ePub File Size: 1.98 Mb
ISBN: 774-3-95536-733-1
Downloads: 13120
Price: Free* [*Free Regsitration Required]
Uploader: Arar

Apply an input source signal to your amplifier. Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. The unit also provides a way to rear mount the unit into a rack for added security.

It will allow brief clipping of peaks and xj only activate when continuous, hard clipping occurs. Insert the bare wire into the hole that was reveled by unscrewing the binding post cap.

American Audio Stereo Amplifier V/V User Guide |

A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself. For cable runs ameerican than 20ft.

Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. This may reduce the buzz that is caused from an electrical 60Hz cycle.

Mobile ADJ Product Parts – Lighting Online Parts Store

Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. Turning the knob in a clockwise direction will increase signal output.


Turn channel two gain up. Service Hours are Monday through Friday 9: Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems. To prevent electrical shock or fire hazard, do not expose this amplifier to rain or moisture.

Connect your inputs into channels one and two of the amplifier.

American Audio V3000/V2000 Stereo Amplifier User Manual

Be sure that supplied voltage matches that of the required voltage of you amplifier. Power Switch – This switch controls the units main power. Under heavy clipping activity lower the channel one gain control to reduce the risk of damage to your speakers and amplifier.

Always be sure the source voltage for your areas matches the ammerican voltage for your amplifier.

Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack.

You may also visit us on the web at www. Connect a XLR cable to the input of channel one. These amplifiers are designed to provide a big impact in sound reproduction.

Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. To reset the breaker, push it in.


American DJ V3000 2 Channel Professional Stereo Amplifier

The diagram below detail the functions of each dip switch, the functions are also printed on the rear panel of the amplifier. Always use the 50 Hz filter setting if you are using the amplifier to drive b3000 distributed line system also known as a constant-voltage line, 70 volt line, etc.

Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

An ultrasonic network uncouples RF from the output and helps keep the amplifier stable with reactive loads. Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal.

Please do not return the amplifier to your dealer without contacting customer support. Cooling Fan – Dual speed cooling fans.

This booklet contains important information concerning the proper and safe operation of your new amplifier. Channel 1 filters is control by dip switch 1 and channel 2 filter is controlled by dip switch 4. Turn your input source level up.

Turn your equipment on your amplifier xmerican always be the last item you turn on. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector. Antes de usar este amplificador, lea mas advertencias en la guia de operacion.