Thyro-A is an international registered trademark of AEG Power. Solutions GmbH. Windows and Windows NT are registered trademarks of the Microsoft. The Thyro-A is a communication-capable Thyristor Power Controller. synchronization option (in TAKT operating mode with Thyro-Power Manager option) and. These operating instructions are part of the Power Controller Thyro-A. . change parts not approved by AEG SVS as well as any other use of Thyro-A is not.
|Country:||Antigua & Barbuda|
|Published (Last):||21 February 2015|
|PDF File Size:||2.83 Mb|
|ePub File Size:||20.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
Sign in to check out Check out thyroa guest. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.
If the limit has been reached, the red Eag blink in 1 sec. NOTE The contact for actuating the pulse lock must be light-duty contact. Type name, production number, complaint, ambient conditions, operating mode, duration of use.
Eunder preparation, with consideration to Canadian National Standard, project no. This produces the following absolute limiting values: The value is set by potentiometer R Subject to credit approval. Handling These operating instructions for Thyro-A are set out so that all work required qeg commissioning, maintenance and repair may be performed by corresponding specialist personnel.
Seller information harpoonplc Mains load Contents Sync. Special financing available Select PayPal Credit at checkout to have the option to pay over time. Shipping cost cannot be calculated. For all other settings the following applies: As a result, the time up to the initial switch-on varies. The also applies to the operating mode VAR. They are only read in by the Power Controller once when switched on or with mains recovery.
AEG THYRO-A Operating instructions |
Image not available Photos not available for this variation. The following controllers receive their impulses at X2. If this limit is undercut, an indication shows. The information given below must be understood in this respect.
Please enter 5 or 9 numbers for the ZIP Code. Learn More – opens in a new window or tab International shipping and import charges paid to Pitney Bowes Inc.
Aeg THYRO-A Manuals
Therefore, wait for a minimum of two hours before commissioning. Sales tax may apply when shipping to: Report item – opens in a new window or tab. Setting Phase angle 1. These are described below. For default settings see chapter 8. With the last controller X2. On delivery the device is parameterized and adjusted to the respective power section. Additional information and notes for unqualified persons and for the use of Thyro-A outside of industrial installations are not contained in these operating instructions.
All other aet and product names are the registered trademarks of the respective owners. Please enter a number less than or equal to 4. These operating aeh are part of the Power Controller Thyro-A.
AEG THYRO-A Manuals
The full wave switch mode is especially suited for loads with thermal inertia. It then switches the analog output over so that instead of the actual value, the poti value is read out.
The following zeg are essential for operating the device: Add to watch list Remove from watch list.
Thyro-A 2A load in delta connection e. Further details on the pulse lock are described in the chapter of the same name. It is possible to compensate these by using circuit variants.
Due to the nature of surplus and or used items, no guarantees or warranties are either expressed or implied. Should there be a flicker, this can be minimized with the aid of the mains load optimization.
Abbreviations In this description the following specific abbreviations are used: During the setting procedure an instrument connected to the analog output indicates the aaeg value. This amount is subject to change until you make payment. We are surplus material dealers and do not have the ability or knowledge to test items for functionality.
For Thyro-A 2A wih load in delta connection a setting for load monitoring can be made according to the table below: The connection output for the control device is ca. The distance between the Power Controller and the cabinet ceiling or other mountings should be at least mm.